{"id":188,"date":"2019-12-13T09:00:29","date_gmt":"2019-12-13T09:00:29","guid":{"rendered":"http:\/\/www.stepperchina.com\/?p=188"},"modified":"2019-12-13T09:00:29","modified_gmt":"2019-12-13T09:00:29","slug":"how-to-improve-step-motor-performance-with-encoder","status":"publish","type":"post","link":"https:\/\/www.stepperchina.com\/index.php\/2019\/12\/13\/how-to-improve-step-motor-performance-with-encoder\/","title":{"rendered":"How to Improve Step Motor Performance with Encoder"},"content":{"rendered":"\n

Step motors<\/a> are widely used in automation due to their high resolution, precision positioning, minimal control electronics, and low cost. As an open loop system, traditional step motors are driven without the need for sensors to feed information back to a controller; however, the open loop configuration of step motors has challenges.<\/p>\n\n\n\n

ENCODER FUNCTIONALITIES<\/strong>
Figure 1.< By adding an inexpensive encoder to a step motor system, the drive\/controller can monitor the motor’s actual position, closing the feedback loop and avoiding many of the limitations traditionally associated with stepper systems.<\/p>\n\n\n\n

\"How<\/figure>\n\n\n\n

The addition of an stepper motor encoder<\/a> to the step motor system (Figure 1) adds functionality to detect and even prevent stalls by providing feedback to the drive. Depending upon how an operator programs the controller, encoder feedback can verify motor position, immediately detect motor stall, prevent motor stall, and create a closed loop servo system.<\/p>\n\n\n\n

Position Verification<\/strong> \u2014 When pushed beyond its limits, a step motor will stall before reaching the endpoint. This event typically occurs when motors are not adequately specified for high-cycle applications. An encoder can provide position feedback at the end of the motion profile, indicating if the step motor stopped before reaching the end position<\/p>\n\n\n\n

Stall Detection <\/strong>\u2014 Stall detection notifies the user\/system\/machine as soon as a motor stall occurs, eliminating the uncertainty of whether or not the motor reached its target position. A more advanced function than position verification, stall detection (Figure 2) enables the controller to compare the registers of the encoder counts and target motor position on a continuous basis instead of just at the end of the move.<\/p>\n\n\n\n

Stall Prevention<\/strong>\u2014 While greatly increasing system functionality, stall detection does not inherently improve step motor performance; it still requires the operator to perform a corrective move and re-reference the axis to the home position. Stall prevention, on the other hand, dynamically and automatically adjusts the move profile to prevent a stall, enabling the motor to operate with constant torque to get into an accurate end position without stalling.<\/p>\n\n\n\n

Servo Control and Increased Motor Torque<\/strong> \u2014 Using encoder feedback to servo-control, a step motor increases motor torque for greater dynamic performance. With peak torques up to 50% higher than the rated holding torque of the motor, the servo-controlled step motor system can operate at higher acceleration rates and with higher throughput for faster machine cycles.<\/p>\n\n\n\n

\"How<\/figure>\n\n\n\n

When working as part of a fully closed loop stepper motor system<\/a>, step motors run cooler, more efficiently, quieter, and with faster settling times than their open loop counterparts. Unlike the other encoder applications described here, servo control applies a peak torque that enables the motor to get past stall conditions without sacrificing speed. Some manufacturers offer motors (Figure 3) already preconfigured with a high-resolution incremental encoder and closed-loop servo control firmware.<\/p>\n\n\n\n

\nhttps:\/\/blog.oyostepper.com\/2019\/12\/13\/what-is-a-stepper-motor\/\n<\/div><\/figure>\n","protected":false},"excerpt":{"rendered":"

Step motors are widely used in automation due to their high resolution, precision positioning, minimal control electronics, and low cost. As an open loop system, traditional step motors are driven without the need for sensors to feed information back to a controller; however, the open loop configuration of step motors has challenges. ENCODER FUNCTIONALITIES Figure … Continue reading “How to Improve Step Motor Performance with Encoder”<\/span><\/a><\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[],"tags":[],"class_list":["post-188","post","type-post","status-publish","format-standard","hentry"],"_links":{"self":[{"href":"https:\/\/www.stepperchina.com\/index.php\/wp-json\/wp\/v2\/posts\/188","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.stepperchina.com\/index.php\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.stepperchina.com\/index.php\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.stepperchina.com\/index.php\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.stepperchina.com\/index.php\/wp-json\/wp\/v2\/comments?post=188"}],"version-history":[{"count":1,"href":"https:\/\/www.stepperchina.com\/index.php\/wp-json\/wp\/v2\/posts\/188\/revisions"}],"predecessor-version":[{"id":191,"href":"https:\/\/www.stepperchina.com\/index.php\/wp-json\/wp\/v2\/posts\/188\/revisions\/191"}],"wp:attachment":[{"href":"https:\/\/www.stepperchina.com\/index.php\/wp-json\/wp\/v2\/media?parent=188"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.stepperchina.com\/index.php\/wp-json\/wp\/v2\/categories?post=188"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.stepperchina.com\/index.php\/wp-json\/wp\/v2\/tags?post=188"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}